Guide
Front squat vs back squat: which to program, and how to run both in one block
The two squats load the trunk and the quads differently. Pick the main lift by what the block is for, then by what limits the lifter, and use the fix table and the four-week block below to run both.
By RaiNGE product teamUpdated 8 min read
Written for coaches choosing the main squat for a client or deciding whether to program both.
See the back squat on Lower A and the front squat on Lower B of a 4-day upper lower week, with the rules to progress both. See the 4-day program
On this pagePick the main squat by what the block is for
Pick the main squat by what the block is for
Both squats train the legs hard, and they load the body differently. The front squat holds the bar on the front of the shoulders, so the torso stays more upright and the quads and upper back tend to do more of the work. The back squat leans forward more, so the hips and lower back share more of it, and it usually moves more weight.
Then check what limits the lifter
Plenty of lifters have the legs for a front squat and lose it at the rack. Find what gives out first, because most front squat limits have a setup fix that keeps the lift in the program.
If two fixes in a row fail, make the back squat the main lift and keep the front squat as a lighter second-day lift. When neither barbell squat fits, the squat alternatives guide has the closest-first ladder and the starting prescriptions.
Run both lifts in one four-week block
With two lower days a week, give each squat its own day and its own progression: back squat on Lower A and front squat on Lower B, at least two days apart, as in the 4-day upper lower split. With one lower day, alternate the two squats week by week. Treat every number here as a starting point.
Progression rule. Add 2.5 kg (5 lb) to a lift after a week in which every set reached 6 at RPE 8 or less, and for the front squat only if the elbows stayed up on the last rep of every set. Each squat trains once a week here, so the block fixes the target at 6 reps where the double progression guide uses a range, and one clean week earns the jump. A lift that misses holds its load, and two sessions in a row without progress cut it by 10%, as that guide describes. This block sets no deload: the deload week guide says when to call one.
Worked example: a 100 kg back squat and a rack that gives out first
Your client back squats 4×6 at 100 kg (220 lb), RPE 7-8, and you add a front squat day. About 75-80% of that load is 75-80 kg (165-176 lb). Open at 75 kg for 3×6 with the 1-second pause, because the first session is also a test of the rack.
Say the first set finishes with the legs at RPE 6, but on rep 5 the elbows drop and the bar rolls toward the fingertips. The load suits the legs and the rack cannot hold it yet. Work down this order, and stop at the first change that clears the fault.
- 1
End the set at the first fault
Log 4 reps. Every rep after the elbows drop rehearses the fault.
- 2
Change the hold before the load
Use two or three fingers under the bar with the elbows high. If the wrists or lats still limit the rack, switch to straps or the cross-arm rack. The legs have not changed, so stay at 75 kg.
- 3
Shorten the set
If the rack still gives out at rep 5, run 4×4 at 75 kg, then build back to 3×6 as every set stays clean.
- 4
Hold the rack longer at a lighter load
If the elbows still drop, take about 10 kg (22 lb) off to 65 kg (143 lb) and pause 2 seconds at the bottom of every rep for 3×5. Rebuild the load from there.
- 5
Decide after two weeks
If the rack still ends sets before the legs do, the front squat is not ready to carry load yet. Use a safety-bar squat or a double-dumbbell front squat on Lower B, keep light front squats in the warm-up, and retest next block.
When pain is the reason for the change
At 3-5/10 in the front rack, the setup changes in the fix table come after a lighter load. For knee pain at the bottom of either squat, the knee-friendly quad exercises guide orders the options by knee bend under load, and the pain scale guide covers each band.
In RaiNGE, when a coach asks for a swap, the AI suggests a few alternatives, the safety rules drop any that conflict with the client's flags, and cautioned options are listed last. A low-back flag, for example, keeps barbell squats out of the AI draft, and both lifts on this page are barbell squats. Cautions are shown to the coach, who decides what fills the squat slot.
Common questions
What is a good front squat to back squat ratio?
About 75-80% is a starting point, the figure the squat alternatives guide uses, and a lifter's own ratio can sit well off it. Limited rack or ankle range tends to pull it down, and lifters who train the front squat often sit higher. Use the ratio to pick the first load, then let the sets decide.
Can you front squat and back squat in the same session?
Yes, if the second lift is light. Put the lift that matters most for the block first, because the second one runs on a tired upper back and trunk, and 2×6 at RPE 6 is a reasonable second lift. For a strength block, two separate lower days give each lift a full dose.
Should beginners learn the front squat or the back squat first?
Neither has to come first. Start with a goblet squat or box squat, then add the barbell squat whose bar position the client holds comfortably: the front rack asks for wrist, lat, and upper-back range, and the back squat asks for shoulder comfort under the bar. Teach one at a time. The goblet squat alternatives guide covers the step before either.
Does front squat strength carry over to the back squat?
Some carryover is likely, because both train the legs and the trunk, but a back squat test needs back squat practice. If the client will be tested on the back squat, keep one back squat session in every week of the block and use the front squat as the lighter second lift.