Guide
How to restart training after a break: load, volume, and ramp by layoff length
Most advice says to start light and build back. This guide sets the restart load, first-week sets, and ramp from the length of the break, then runs a four-week squat ramp with a hold rule for each week.
By RaiNGE product teamUpdated 8 min read
Written for coaches restarting a client who has been out for weeks or months.
Once the ramp is done, this template gives a returning intermediate client heavy, light, and medium days to run, with a fallback for a two-session week. Use the 3-day full-body program
On this pageStart from the length of the break and the old working load
Start from the length of the break and the old working load
Two inputs set the restart: how long the client has been out, and what they were lifting before. Take the second from the log: the heaviest load the client handled for all sets at RPE 8 or less across their last four good weeks. A one-off best set is not the old working load.
These rows agree with the returning-client row in the deload week guide: about a week away, cut the load 10%, and two weeks or more, cut both sets and load.
RPE and reps in reserve outrank every percentage. If 70% of the old load rates RPE 8 on the first set, the load is too heavy today, so cut it. If 80% rates RPE 4, hold the planned load anyway and let the ramp set the pace. The RPE scale guide explains reps in reserve.
Adjust the row for what the client is restarting after
The reason for the break changes how far to trust the calendar. Ask before the first session, and move one row longer when the answer is worse than the length of the break suggests.
Worked example: a squat back after 8 weeks off
Example: one client squatted 4×6 at 100 kg (220 lb) at RPE 8 before eight weeks away, with no illness or injury. That is the 7-12 week row: 70-75% of the old load, about half the sets, and about 5% more each week. The client squats twice a week, and both sessions use the week's prescription. The numbers are an illustration.
Move up a week only when all four are true
- Every set stayed at or under the week's RPE target.
- Soreness was 3/10 or less at the next warm-up and passed the soreness screen.
- Pain was 0-2/10 and familiar.
- Both sessions happened at full prescription. A trimmed or cut session does not count, so repeat it first.
If one item is false, hold the week by repeating its prescription once. If the same week fails twice, drop back to the previous week's load and ask what changed outside training. The ramp is a ladder, not a calendar: week 4 can fall in calendar week 6. Once the client is back at 100 kg for 4×6 at RPE 8 or less, normal double progression takes over.
Why the first week feels easy and the soreness comes later
The first session feels easy because the plan made it easy: 70% of the old load for half the sets leaves the client fresh, and the movement is familiar.
Soreness runs on a different clock. It is usually strongest one to three days after the session, so how the client feels on day one says little about day three. That is the reason to hold the plan after an easy first session: week one is a tolerance test, and the answer arrives later.
- 1
Session 1: finish easy, and say why
Run week 1 at RPE 5-6. Tell the client: you will feel good today, and soreness may show up in a day or two.
- 2
The next morning: ask for a number
Message the client for soreness from 0 to 10 and where it sits. Compare it with the three-question screen on the soreness page.
- 3
Before session 2: ask again
Train as planned at 0-3/10, trim the sore region at 4-6/10 (drop a set or cut load 5-10%), and train another region at 7/10 or more. Joint, sharp, or movement-changing symptoms are pain, so use the bands below.
Readiness and pain rules during the ramp
Returning clients arrive tired or sore more often than clients mid-block, so run a short check-in before every ramp session. These are the same bands the low-readiness guide uses:
- Readiness 70% or more: Train as planned.
- Readiness 60-69%: Trim: drop a set or cut load 5-10%.
- Readiness under 60%: Cut: drop a set, cap effort at RPE 7, and lengthen rest.
A trimmed or cut session still counts as training, but it does not count as a clean session toward moving up. In RaiNGE, a check-in with readiness under 60%, pain of 4/10 or more, fatigue of 8/10 or more, or sleep quality of 4/10 or less creates a pending adjustment for the coach, with the trigger, the check-in data, the reasoning, and the proposed before-and-after values. Nothing changes the plan until the coach approves it.
Common questions
Can a client skip a step in the ramp if week one feels easy?
Once, and only on evidence. If both week-one sessions finished at RPE 5 or lower and soreness was 3/10 or less at the next warm-up, take a 10% load step in week 2 instead of 5%, and keep the sets as written. If soreness is 4/10 or more, hold the week. Never skip the check to save a week.
When can a returning client test an old max?
After the ramp is finished and the client has lifted the old working load for all sets at RPE 8 or less, which is week 7 in the example above. A coach can also skip max tests and use a set of 5-6 reps at RPE 8 as the check. Do not test during the ramp.