Skip to content

Program template

A 12-week basketball off-season strength program with a jump-contact budget

Most off-season plans stop at the exercise list. This one counts foot contacts, places the three lifting days around court work, and says what to cut first when the week is heavy.

By RaiNGE product teamUpdated 11 min read

Written for coaches training basketball players through a 12-week off-season.

Jump to the weekly template

Short answer

A basketball off-season strength program runs three lifting days a week for 12 weeks in three phases: general preparation, strength, then power and jumping. Lifts progress by double progression, jumps by landing quality and a foot-contact budget, and every fourth week is lighter. When the week's load is high, cut jump contacts first.

  • Run it for athletes with a lifting base, no current pain, and three lifting days a week next to court work. A pain flag means the pain bands and swaps come first.
  • Start from a contact budget, counting single-leg and drop landings twice: 30-40 per jump session in weeks 1-4, 50-70 in weeks 5-8, 70-100 in weeks 9-12. The figures are our starting points, not a published standard.
  • When load across lifting, court work, and games is high, cut in this order: contacts, then sprint volume, then sets, then load.

Answer a short intake and RaiNGE emails you one workout as a PDF, with sets, reps, and effort targets to check against this template. Get a free sample workout

On this pageWho this program fits, and who it does not

Who this program fits, and who it does not

It suits basketball players with six or more months of consistent lifting, stable squat, hinge, and press technique, and no current pain, who can lift three days a week next to practice and skill work. Sessions run 45-60 minutes. New lifters belong on the 12-week beginner strength program. For three full-body days without the jump work, use the 3-day full body workout program.

Run the program when the athlete passes every check.
CheckRun it whenUse something else when
Training base6+ months of consistent lifting with stable technique. No jump background is needed, because phase 1 starts with landingsThe athlete is new to lifting
ScheduleThree non-consecutive lifting days fit next to practices and skill workOnly two days hold, or it is in season: use the in-season version below
Pain statusAny pain in training is 0-2/10 and familiarA current pain flag: use the pain bands and the substitution rules first
Age18 or olderUnder 18: a coach qualified for youth training adapts the plan
EquipmentBarbell and rack, bench, dumbbells, trap bar, 30-60 cm (12-24 in) box, medicine ball, pulldown or pull-up bar, cable stack, and a jump surface with some give, such as a court floorNo trap bar, box, or jump surface: use the substitution table
Run the program when the athlete passes every check.

The 12 weeks: three phases, and where the lifting days go

Each phase lasts four weeks: three weeks of adding load, then a lighter week. Weeks 1-4 are general preparation, weeks 5-8 are the strength phase, and weeks 9-12 are the power and jumping phase. Exercises stay the same inside a phase.

The days are named by what they train: Day 1 is lower-body strength with jumps, Day 2 is upper body with no jumps, and Day 3 is single-leg work and power with jumps. Three rules hold every week: jumps come first in a session, while the athlete is fresh; the two jump days sit at least 48 hours apart; and nothing heavy and no jumping lands on the day before a game.

Where the three lifting days fall in a court week.
Court weekLifting daysWhy
Practices and skill work, no gameDay 1 Monday, Day 2 Wednesday, Day 3 FridayDay 1 goes on the day with the lightest court work
One game on SaturdayDay 2 Sunday, Day 1 Tuesday, Day 3 ThursdayThe upper-body day follows the game, the heavy day sits four days before the next, and Friday stays free
Two games, or a tournamentRun the in-season version that weekGame load is already high, so the cut order below applies
Where the three lifting days fall in a court week.

The three training weeks, one for each phase

Each block is one week, repeated for the three loading weeks of its phase. Doses are starting points a coach adjusts. Numbers in brackets are counted jump contacts, and stick means hold the landing for 2 seconds. The rules under weeks 1-4 apply in every phase, and the pain scale for exercise and adjusting a workout for low readiness explain each band.

Weeks 1-4: general preparation

Main lifts 3×8-10 at RPE 6-7, rest 90-120 seconds. Jump drills come first, with 60-90 seconds between sets. Week 4 is the lighter week: sets cut 40-50%, same loads.

Day 1

Lower strength

Squat, hinge, and the first landings

Stick landing
3×6 (18)
Countermovement jump, stick
3×4 (12)
Barbell back squat, 3-second lowering
3×8-10
Romanian deadlift
3×8-10
Incline dumbbell press
3×8-10
Chest-supported dumbbell row
3×8-10

Day 2

Upper and trunk

Press, pull, and carry, no jumps

Barbell bench press
3×8-10
Pull-up (assisted if needed)
3×6-8
Half-kneeling dumbbell press
3×8/side
Seated cable row
3×10-12
Pallof press
2×10/side
Farmer carry
3×30-40 s

Day 3

Single-leg and power

Single-leg strength and a second landing day

Countermovement jump, stick
3×6 (18)
Broad jump, stick
3×4 (12)
Rear-foot elevated split squat
3×8-10/side
Barbell hip thrust
3×8-10
Lat pulldown
3×10-12
Side plank
3×20-30 s/side

When to adjust

Readiness 70% or more
Train as planned
Readiness 60-69%
Trim: drop a set or cut load 5-10%. On a jump day, cut contacts by a third first
Readiness under 60%
Cut: drop a set, cap effort at RPE 7, and lengthen rest. On a jump day, keep stick landings only, 20 contacts at most
Pain 0-2/10 and familiar
Continue and monitor
Pain 3-5/10
Reduce load or range first, then adjust the setup, then change the exercise. On a jump, range is box height or distance
Pain 6-7/10
Stop the movement that provokes it and choose a conservative alternative
Pain above 7/10, or sharp, worsening, radiating, or unfamiliar pain
Stop loading and refer to a qualified professional
Every set tops the range at RPE 7 or less
Add the smallest load jump

Weeks 5-8: strength

Main lifts 4×4-6 at RPE 7-8 with 2-3 minutes of rest, other lifts 3×6-10. Jump drills come first. Week 8 is the lighter week: sets cut 40-50%, same loads.

Day 1

Lower strength

Heavy squat and single-leg landings

Box jump, step down
4×5 (20)
Single-leg stick landing
3×3/leg (36)
Barbell back squat
4×4-6
Romanian deadlift
3×6-8
Incline dumbbell press
3×8-10
Chest-supported dumbbell row
3×8-10

Day 2

Upper and trunk

Heavier press and pull, no jumps

Barbell bench press
4×4-6
Pull-up (assisted or weighted)
4×4-6
Standing dumbbell press
3×6-8
One-arm dumbbell row
3×8/side
Pallof press
3×10/side
Farmer carry, heavier
3×30-40 s

Day 3

Single-leg and power

Trap bar deadlift and drop landings

Countermovement jump, stick
4×6 (24)
Drop landing
4×4 (32)
Trap bar deadlift
3×4-6
Rear-foot elevated split squat
3×6-8/side
Seated cable row
3×8-10
Side plank
3×30 s/side

When to adjust

Every set tops the range at RPE 8 or less
Add the smallest load jump
A landing misses the standard
Repeat the rung with no added height or distance
Readiness or pain flag
Use the rules under weeks 1-4

Weeks 9-12: power and jumping

Main lifts 3×3-5 at RPE 7-8, moved fast, with 2-3 minutes of rest. Jump drills come first. Week 12 is the lighter week: sets cut 40-50%, same loads.

Day 1

Lower strength

Fast squat and the heaviest landing day

Box jump, step down
3×5 (15)
Single-leg stick landing
3×3/leg (36)
Drop landing
3×4 (24)
Barbell back squat
3×3-5
Romanian deadlift
3×5-8
Incline dumbbell press
3×6-8

Day 2

Upper and trunk

Fast pressing and pulling, no jumps

Barbell bench press
3×3-5
Pull-up (assisted or weighted)
3×4-6
Medicine ball chest pass, fast
3×5
Standing dumbbell press
3×6-8
Pallof press
3×10/side
Farmer carry
3×30-40 s

Day 3

Single-leg and power

Trap bar deadlift and lateral power

Countermovement jump, stick
4×6 (24)
Lateral bound, stick
4×3/side (48)
Trap bar deadlift
3×3-5
Rear-foot elevated split squat
3×6-8/side
Seated cable row
3×8-10
Side plank
3×30 s/side

When to adjust

Every set tops the range at RPE 8 or less
Add the smallest load jump
A landing misses the standard
Repeat the rung with no added height or distance
Readiness or pain flag
Use the rules under weeks 1-4

Jump contacts: the landing standard, the ladder, and the budget

A landing meets the standard when it is quiet, on the whole foot, with the knees tracking over the middle toes, the trunk tall, and the position held for 2 seconds. Move up a rung, or add height or distance, only after every landing in two sessions in a row meets it, and change one thing at a time.

The jump ladder, from the floor up, with how each landing is counted.
RungJumpCounts as
1. Stick landingA small vertical jump, landing on both feet1
2. Countermovement jumpA full-effort vertical jump, landed and held1
3. Broad jump or box jumpA jump for distance, or onto a 30-60 cm box with a step down1
4. Single-leg stick landingA small hop forward, landed and held on one leg2 (double)
5. Drop landingStep off a 30-40 cm box and land on both feet2 (double)
6. Lateral boundPush off one leg sideways, land and hold on the other2 (double)
The jump ladder, from the floor up, with how each landing is counted.

Count each landing once and each single-leg or drop landing twice, so 3 single-leg landings on each leg is 12 contacts. Weeks 9-12, Day 1 adds up to 15 + 36 + 24 = 75 contacts. Counting those landings twice is a convention this plan uses, not a published rule, and the budgets below are our own starting points, not a sourced standard. A coach adjusts them to the athlete.

Starting contact budgets per jump session by phase, counted as above.
WeeksContacts per jump sessionRungs in playLighter week
1-430-401-3, from the floor15-20
5-850-701-5, boxes up to 45 cm25-35
9-1270-1001-6, boxes up to 60 cm35-50
Starting contact budgets per jump session by phase, counted as above.

The blocks above sit near the bottom of each band. Add a set to one drill only when the landing standard held for two sessions and the week is not heavy. Cutting every drill to 2 sets in a lighter week puts each day in the last column.

How the lifts progress, and what to cut first when load is high

The strength lifts follow double progression. Hold the load until every set tops the range at RPE 7 or less in phase 1 and RPE 8 or less after that, then add 2.5-5 kg (5-10 lb) to lower-body barbell lifts or 1-2.5 kg (2.5-5 lb) to upper-body lifts, and return to the bottom of the range. These ranges are 2 reps wide, narrower than the guide's 3-5, on purpose: the jumps are small (2.5 kg is 2.5% of a 100 kg squat, about one rep), so a narrow range still moves smoothly, and each phase holds one rep target. Jumps progress up the ladder above.

Example: a phase 2 back squat, 4×4-6 at 100 kg (220 lb), RPE 8. Week 5 gets 6, 6, 5, 5. Week 6 gets 6, 6, 6, 6, so the jump is earned. Week 7 moves to 102.5 kg (226 lb) and gets 5, 5, 5, 4. Week 8 is the lighter week at that load, 2×4-6. Week 9 opens phase 3 at 102.5 kg for 3×3-5, and the first session's RPE shows whether it fits.

Weeks 4, 8, and 12 use method 1, cut the sets, from the deload week guide: working sets drop 40-50%, rounded to whole sets (4 become 2, 3 become 2), loads and reps stay, every set stays at RPE 8 or lower, and conditioning stays conversational. Add no new lifts or max tests. The guide plans a deload after 3-5 weeks of heavy or high-volume work for an advanced lifter and after 4-6 weeks of adding load for an intermediate. Court work adds load the training log does not show, so this plan uses three loading weeks, shorter than the guide's window. That is a starting point, not a tested rule, and a coach can lengthen it for an athlete whose log and court week both stay easy. Two warning signs in one week call a lighter week early.

When load across lifting, court work, and games is high, work down this list and stop at the first cut that is enough. The readiness bands size a cut for one session. This order says what goes first.

  1. 1

    Jump contacts

    Cut the day's contacts by a third, then to stick landings only. The court already supplies jumps and landings, so this is the cheapest cut.

  2. 2

    Sprint volume

    Take out the last repeat of each sprint set, or swap hard intervals for an easy pace.

  3. 3

    Sets

    Drop the last set of each lift: 4×4-6 becomes 3×4-6. Leave the loads alone.

  4. 4

    Load

    Cut load 5-10% last, so the lifts keep their heavy practice and progression can resume at the load you left.

Adapt it: the in-season week and the substitution rules

In season, run two full-body sessions of 30-40 minutes with 2-3 sets per lift and the loads from phase 3, as the team-sport row in how to choose a training split sets out. Put the heavier session at least two days before the next game. Jumps drop to 10 contacts a session.

In-season maintenance: two full-body sessions, 2-3 sets per lift.
SlotSession A: heavierSession B: lighter
JumpsCountermovement jump, stick: 2×5Stick landing: 2×5
Squat or single legBarbell back squat: 3×4-5Rear-foot elevated split squat: 2×6/side
HingeRomanian deadlift: 2×6Trap bar deadlift: 2×4-5
PushBarbell bench press: 3×4-5Standing dumbbell press: 2×6-8
PullChest-supported dumbbell row: 3×6-8Pull-up: 3×5
TrunkPallof press: 2×10/sideSide plank: 2×30 s/side
In-season maintenance: two full-body sessions, 2-3 sets per lift.
Substitutions that keep each slot's job.
ProblemSwap toKeep in mind
No trap barA conventional deadlift at 5-10% less than the trap bar load, with the same sets and repsGrip and setup limit the first week before the legs do. See trap bar deadlift vs deadlift
No boxBroad jumps and countermovement jumps, with floor stick landings in place of drop landingsCount them the same way and keep the phase's budget
No jump surfaceMedicine ball throws, 3×5, and kettlebell swings, 3×8, in place of the jump drillsContacts drop to zero, so keep the lifts and lighter weeks as written
A flagged knee or ankleApply the pain bands to each exercise first. If a landing provokes it, step down a rung or use throws. If squats do, use a box squat above the painful depth or a leg press in a comfortable rangeRestart jumps at rung 1 once landings stay at 0-2/10 and familiar. See knee friendly quad exercises and leg press alternatives
Substitutions that keep each slot's job.

In RaiNGE, drafts start from athlete context, including injury and pain notes, and safety rules keep exercises that conflict with flagged limitations out of the draft. A coach reviews, edits, and approves the program before it reaches the athlete.

Common questions

Do you count the jumps a player makes in practice and games?

No. Practice and game jumps are hard to count reliably, so the budget covers only the drills you prescribe. Ask the player how the court week felt, and use the cut order when it was heavy.

What if a player starts the program straight after a long season?

Start with a lighter week, as the deload guide schedules after a competition or a peak: phase 1's week at 2 sets per lift and jump drill (20 contacts a jump day), loads at RPE 6. Then run week 1 as written.

How should a coach track jump progress?

Track the rung and the landing standard first, because height only counts once landings pass. If you test jump height, use the same countermovement jump on the same surface, before lifting, in the first session of weeks 1, 5, and 9, and compare a player only with their own earlier numbers.

Next step

Answer a short intake and RaiNGE emails you one workout as a PDF, with sets, reps, and effort targets to check against this template.